Allen Bradley XM Serial Communication Cable Allen Bradley XM Serial Communications Cable, catalogue number 1440-SCDB9FXM2. Connects a PC to an.
various electronic devices and components not included in other sections. Forward to / Arduino / ATEN / Avocent / Bayer / Crypton / Danfoss / Dell / DeltaOhm / Device / Futaba / HP / Imax / Olimex / Pico Allen / Toa / Welch pinouts
Allen Bradley XM Serial Communication CableAllen Bradley XM Serial Communications Cable, catalogue number 1440-SCDB9FXM2. Connects a PC to an Allen Bradley XM series protection module using RS-232.
Apple iPod Touch 2G Internal 5-pin circuitboard connection The propietary Apple miniplug female connector for iTouch 2G and maybe others has 5 pins. The Tip has two connections, to detect if a plug is inside. When both sides are shorted, the internal speaker is shut down. When open after shorted, the music stops (same as removing the earphones)
EasyPic 5..6 IDC ConnectorEasyPic5 or EAsyPic6 IDC Board Connection
External POST controller LPTused for attachment of external LPT POST card to PCI POST controller
Heidenhain TNC 407 / 415 / 425 LCD connectionused to connect LCD monitor to Heidenhain TNC 407 / 415 / 425 at the pole X43 in replacement of old Screen VDU (BC 110) You can and should connect all GND together i both ends. The shield for RGB could also be connected but I have not tried yet to do that.
Inter-M LM-88 Remote controller
iRobot Roomba Open Interface (OI) The Roomba Open Interface (OI) is a software interface for controlling and manipulating Roomba?s behavior. The software interface lets you manipulate Roomba?s behavior and read its sensors through a series of commands, including mode commands, actuator commands, song commands, and sensor commands that you send to the Roomba?s serial port by way of a PC or microcontroller that is connected to the Mini-DIN connector.
j-link JTAG - KRL v1 STM32 PCB interface cableJtag cable for old KRL radio modems
JTAG Header for FPGA/CPLD Applications (Comcom Electronics Standard)
LPC Xpresso LinkLPC Link pinout on the LPC Xpresso boards
Microchip ICD interconnect for PIC programmers
Nortel Meridian Opt 11 PBX RS-232 Terminal CableThis cable is used to allow terminal access to a Nortel Meridian Opt 11 PBX.
Omron PLC to RS-232 calbeOmron PLC's Periherial connector to PC RS-232 cable Offical cable names: CQM1-CIF02 or CS1W-CN226
OP-400 Automation Direct HMI Programing and Communications Connector
Rackbotz 303 External Sensor PinoutPinout for Rackbotz 303 (and other early Netbotz products) external temperature sensor.
Rokenbok educational toy 1st gen controller
Simatic S7-200 PLCMemory Expansion Slot
Telemann 1650S digital satellite meter RS232 cable
TFT LCD module connectorinternal connectors of LP154WX4 TFT LCD and many others
Arduino Pinouts
Arduino EsploraThe Esplora differs from all preceding Arduino boards in that it provides a number of built-in, ready-to-use set of onboard sensors for interaction. It's designed for people who want to get up and running with Arduino without having to learn about the electronics first.
Arduino EthernetThe Arduino Ethernet is a microcontroller board based on the ATmega328. The Ethernet differs from other boards in that it does not have an onboard USB-to-serial driver chip, but has a Wiznet Ethernet interface. This is the same interface found on the Ethernet shield.
Arduino FIOThe Arduino Fio is intended for wireless applications. The user can upload sketches with an a FTDI cable or Sparkfun breakout board.
Arduino Fishino UNOFishino UNO is based on Arduino platform
Arduino MicroThe Arduino Micro is a microcontroller board based on the ATmega32u4, developed in conjunction with Adafruit. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard.
Arduino MiniThe Arduino Mini is a small microcontroller board originally based on the ATmega168, but now supplied with the 328, intended for use on breadboards and when space is at a premium. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 8 analog inputs, and a 16 MHz crystal oscillator. It can be programmed with the USB Serial adapter or other USB or RS232 to TTL serial adapter.
ATEN Pinouts
ATEN CS1644, CS1744 Firmware Upgrade Cable3.5mm TRRS (4 pin) male to DB9 female
Avocent Pinouts
Avocent / Cybex / BlackBox XPSI and KV1609C serial control cards RJ45connector of the 4XP / XP4000 / XP4040 / ServSwitch Multi EXP
Bayer Pinouts
Bayer Contour Ts Data CableData cable specification for Bayer Contour Ts - Blood Glucose Meter
Crypton Pinouts
Crypton 290 Emission Analyser Serial cableThis is the pinouts for a Crypton Vehicle Emissions Analyser to Computer Serial Cable. Model: 290
Danfoss Pinouts
Danfoss RS-232 serial cable pinoutThis is the pinouts of the original Danfoss cable for ADAP-KOOL Systems PART No : 080Z0262
Dell Pinouts
Dell RD530 Bluetooth cardRD530 Bluetooth Card used in many Dell laptops. Not sure if the connector is a JST 1 mm compatible.
DeltaOhm Pinouts
DeltaOhm HD2110CSNM rs232 serial cableSerial cable used to connect DeltaOhm thermometers to computer using RS232. Part number HD2110CSNM.
Device Pinouts
SMC PTE-100-C PRO - cable PTE-BUSDevice SMC PTE-100-C PRO - cable PTE-BUS
Futaba Pinouts
Futaba Buddy Box ConnectorFutaba Buddy Box
HP Pinouts
HP batteryHP battery pinout
Imax Pinouts
IMAX B6 Balance ChargerIMAX B6 Balance Charger
Olimex Pinouts
Universal EXTension (UEXT) connectorThis connector includes power and three serial buses: Asynchronous, I2C, and SPI. The connector layout was specified by Olimex Ltd and declared an open-project.
Pico Allen Pinouts
PICO ALLEN BRADLEY 1760-xxx connectorConector PICO ALLEN BRADLEY 1760-xxx
Toa Pinouts
TOA Wireless WTU-4800
Welch Pinouts
Welch Allyn VSM 300 Serial DB9F to RJ45This cable connects a PC serial port to a VSM300 via a straight thru RJ45 patch cable
Pin Number
Pin Name
Description (may be empty)
1
?
2
?
3
Gnd
0V
4
+5V
Supply via resistor
5
Rx
Data to PLC rs232 TTL
6
Tx
From PLC to PC TTL 232
Because I can't find good picture of socket, you need to rotate your PLC counter-clockwise - then numbers of pins will be OK.
Rx pin is pull-up'ed to +5V
For conecting to PC you need simply converter on MAX-232, only rx,tx are used.
After powering up PLC, Rx pin is Low about 3 seconds (lcd of plc is blank) , after that - is pull-up'ed.
Model easy 619 from moeller, works (comunicate) with free Allen Bradley PicoSoft :)